Opening Hour

Mon - Sun, 0:00 - 24:00

Call Us

+86-21-58386256

  • Ball milling: a green technology for the preparation and

    9 Jan 2019 Ball milling is a simple, fast, cost-effective green technology with reproducible results due to energy and speed control, applicability in wet and dry the presence of chemical agents, therefore it represents an ideal method 

    Get Price
  • Mechanical milling of aluminum powder using planetary ball milling

    conditions (milling time, ball size, processing control agent (PCA) and speed) in mechanical alloying of aluminum powder to achieve particle size reduction 

    Get Price
  • Effects of Process Control Agents on the Mechanical Alloying

    Powder mixtures with the composition of Nb-20Ti-15Si-5Cr-3Hf-3Al (at.%) were mechanically milled in a planetary ball mill. Normal hexane (5 mass%), methyl 

    Get Price
  • Synthesis of the Mg2Ni Alloy Prepared by Mechanical Alloying

    identified; this phase was probably caused by the presence of the methanol which was used as a control agent during the milling process. It could be assumed 

    Get Price
  • Effects of process-control agents on mechanical alloying of

    The effects of the process-control agents (PCAs) stearic acid and methanol on the mechanical alloying (MA) of a nanostructured aluminum alloy (Al93Fe3Ti2Cr.

    Get Price
  • Influence of calcium process control agent (PCA) on Ti - DORA 4RI

    Influence of calcium process control agent (PCA) on Ti-6Al-4V alloy fabried by high energy ball milling and spark plasma sintering. Abstract. Motivation.

    Get Price
  • Effect of the process control agent in the ball-milled powders and

    1 Apr 2019 Fe-14Cr-0.4Ti-0.25Y2O3 ferritic steels were produced by varying the amount of residual process control agent, PCA (ethanol), in the ball-milled 

    Get Price
  • Chapter 4: Process Control Agents in Mechanical Alloying

    Organic surfactants called 'process control agents' (PCAs) are used to achieve the critical balance between cold welding and fracturing, and enhance the process 

    Get Price
  • an investigation of the use of stearic acid as a process control agent

    Abstract: High energy ball milling of powders involves successive events of fracture and welding promoting mechanical alloying, fine and homogeneous 

    Get Price
  • SURFACTANT-ASSISTED BALL MILLING: A NOVEL ROUTE TO

    Chemical methods to synthesis control- surfactant assisted high energy ball milling has been exploited for the synthesis of various Recently, ball milling process is performed in differ- Surfactants are surface active agents having both.

    Get Price
  • The effect of process control agents and milling atmosphere on the

    High energy ball milling was used with a Pulverisette 5 high-energy planetary ball-mill using a 250 ml hardened steel vial (63 HRC) and hardened steel balls. ( 64 

    Get Price
  • Process Control Agent - an overview | ScienceDirect Topics

    Mechanical alloying is a high-energy, powder manufacturing technique. Constituent powders and sometimes a process control agent (such as a wax- like stearic 

    Get Price
  • Synthesis of nanostructured SnO and SnO 2 by high-energy milling

    8 Aug 2013 The effects of stearic acid on the high-energy ball milling of tin of process control agents on mechanical alloying mechanisms in the Ti-Al 

    Get Price
  • Grinding in Ball Mills: Modeling and Process Control - Sciendo

    in modeling and control of the grinding process in industrial ball mills. Basic depending on whether wetting agents are added to the starting material. Some.

    Get Price
  • Study on Effect of Different Ball Milling Duration on SiC - IJREAM

    milling operation was carried out in inert atmosphere and toluene was used in the study as process control agent. Powder particles in this method are subjected  

    Get Price
  • Effect of process control agent (PCA) on the characteristics - SAIMM

    %. Mechanical alloying. The powder mixtures were milled in a. Simoloyer high energy ball mill using a rotation speed 

    Get Price
  • Study on the Mechanical Alloying Process for Preparing Ag - Core

    optimized, such as reaction environment, process control agent types and dosage, high-energy ball milling time and the composition of. [email protected] intermediate 

    Get Price
  • EFFECT OF COMPOSITION AND MILLING TIME ON THE

    ethanol as a process control agent was added to Keywords: Ni-Cu binary alloys, Mechanical alloying, High-energy ball milling, Nanostructured alloys.

    Get Price
  • What quantity of process control agent to be added while ball milling

    Process control agent (PCA) can strongly influence the size of ball milled powder particles. Experimental results show that the mean particle size is affected by: (1)  

    Get Price
  • Effects of Ball Milling Processing Conditions and Alloy Components

    15 Apr 2019 Although a process control agent (PCA) can be used to reduce the final particle size and increase the powder yield, one need to consider the 

    Get Price
  • Mechanical milling: a sustainable route to induce structural - Nature

    30 Jan 2019 On the other hand, ball-milling process provides an original strategy to modify materials at without the need of any additional reaction or involvement of chemical agents. A blank experiment was done in parallel as control.

    Get Price
  • Role of Sn as a Process Control Agent on Mechanical Alloying

    2 May 2020 Furthermore, the maintenance of said balance allows the milling balls to mill the powder continuously without slowing or halting the process.

    Get Price
  • In uence of Type of Alcohol as the Process Control Agent on Ti-20Ta

    β phase formation after 3 h of mechanical alloying process. Using alcohols as process control agent it is possible to obtain nanocrystalline powders of titanium  

    Get Price
  • Effect of high energy ball milling on the structure of - Techno Press

    It is observed that ethanol as a process control agent (PCA) causes degradation of MWCNT reinforcements after milling for two hours whereas solid stearic acid 

    Get Price
  • Study of Milling Time and Process Control Agent on W–Mo–Cr Pre

    In the preparation process of polishing plate, mechanical alloying (MA) method is used to synthetize pre-alloying powders by means of fierce mechanical action 

    Get Price
  • Effect of Process Control Agents on the FeSiB Powder

    %) was prepared by dry and wet mechanical alloying (MA) route starting from a mixture of Fe, Si and B elemental powders. The mixture was wet/dry milled up to 50 

    Get Price
  • Structural evolution of Fe–Y2O3–Ti powder during ball-milling and

    In this study ball-milling was performed on Fe+10% Y2O3+5%Ti powders for different times without adding a process control agent. Heat-treatment was then 

    Get Price
  • ROLE OF PROCESS CONTROL AGENTS ON MILLING BEHAVIOR

    Keywords: Mechanical alloying; Process control agent, Nano composite, Alumiothermic reduction. 1. Introduction. Mechanical alloying exerts high energy  

    Get Price
  • Process Control Agent - an overview | ScienceDirect Topics

    Mechanical alloying is a high-energy, powder manufacturing technique. Constituent powders and sometimes a process control agent (such as a wax- like stearic 

    Get Price
  • The Effect Of The Amount Of Process Control Agent On The

    Keywords: composite powders, copper matrix composites, electrical contact materials, mechanical alloying, process control agent, tungsten. Keywords.

    Get Price

Related Products